Plumbing Basics: A Must for Bathtub Installation
Plumbing Basics: A Must for Bathtub Installation
Blog Article
Nearly everybody has their own individual perception with regards to Installing A Bathtub.
Setting up a bath tub isn't exactly rocket science, however it does require solid plumbing, woodworking, and in some cases, tiling abilities. Replacing an old bath tub with a new one is also a reasonably tough task. If the old tub is conveniently easily accessible, the job can relocate speedily; if you have to open a wall to remove the old bathtub and position the new tub, the task is a lot harder. In either instance, the job is within a house handyman's skills, although you will certainly need an assistant to vacate the old tub as well as embeded in the new one. Ensure you have actually qualified on your own for the job as well as are comfortable trying it. Instead of working with a specialist to take control of a halfway-completed task, it is better to take into consideration using one before you begin. Chances are you might need a specialist plumber to make tube links.
This post will certainly assist you set up a new bathtub in your washroom if you have actually currently bought a new tub and don't need to alter the plan of your previous water system pipelines.
Your tools and material list ought to consist of the following:
Preparing for the Installment
Firstly, the sustaining framework supplied with the bathroom must be fitted (if required) according to the manufacturer's instructions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is very important to make sure that if the faucet comes with a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the faucets system to avoid strain on the bathtub.
Fit the versatile faucet ports to the bottom of the two faucets making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you utilize every one of the provided washers.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should currently prepare to be suited its last setting.
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your setup, then the first thing you must do is detach the supply of water. After doing so, switch on the faucets to drain pipes any water remaining in the system. The procedure of removing the existing faucets can be rather problematic due to the limited accessibility that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the taps. Have a cloth all set for the staying water that will certainly originate from the pipelines. Once the supply pipelines have actually been eliminated, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from transforming throughout this process. Once the faucets have been eliminated, the holes in the bath/basin will have to be cleaned up of any old sealing substance.
Prior to going on to fit the new faucets, contrast the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the new taps to fit.
Setting up the Bath tub
Making use of the two wooden boards under its feet, place the tub in the called for setting. The wood boards are useful in evenly spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 small points.
The next goal is to make sure that the bathtub is leveled all round. This can be achieved by examining the level and also changing the feet on the tub till the spirit level reads degree.
To mount taps, fit all-time low of the outermost flexible faucet adapter to the appropriate supply pipeline by making a compression sign up with; after that do the exact same for the other faucet.
Switch on the water system and also inspect all joints and new pipework for leaks as well as tighten them if required. Fill the bath tub and likewise inspect the overflow electrical outlet and also the normal outlet for leakages.
Finally, deal with the bathroom paneling as defined in the supplier's instruction manual. Tiling and also sealing around the bathtub ought to wait till the tub has been utilized at the very least once as this will certainly settle it right into its last position.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to stop damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end supplies a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, position the tap in the installing opening in the bath/basin making certain that the washing machines remain in place in between the tap as well as the sink. Secure the faucet in position with the producer provided backnut. Once the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with typical tap adapters. The former type should be linked to the faucet ends first, tightening up just by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the area where the bath satisfies the tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to crack an inflexible seal, triggering the water to penetrate the wall in between the bath as well as the tiling, causing problems with wetness and possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to assimilate your fixtures and also fittings. They are offered in tubes and cartridges, and are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with spins of drenched newspaper or soft rope. Bear in mind to always fill up the tub with water before securing, to allow for the activity experienced when the bathtub remains in use. The sealant can crack fairly very early if you do not think about this motion prior to sealing.
Additionally, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally quickly offered on the marketplace. It is a good idea to fit the ceramic tiles using water-resistant or waterproof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like reading about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Put a short review directly below. We'd be pleased to hear your opinion about this content. We hope that you come back again soon. So long as you appreciated our page please do not forget to share it. I praise you for your time. Don't hesitate to come by our site back soon.
Get answers now! Report this page